Breaking News
Home >> Guides >> Installation Guides >> How to Install Pergo Laminate Flooring

How to Install Pergo Laminate Flooring

Installing laminate flooring is a DIY friendly project, and Bestlaminate is here to guide you how to install Pergo laminate flooring.

Continue your installation


Installing Pergo laminate flooring may look challenging, but it’s actually quite simple. Before you start, make sure you have these flooring installation tools and supplies ready:


  • Tape Measure
  • Measuring tape
  • Pencil
  • Goggles
  • Jig saw with upside down medium teeth
  • Undercutting Saw to undercut door jambs (vibratory undercut saw)
  • Installation Kit (optional)
  • Spacers


  • Laminate flooring
  • Proper underlayment
  • Moldings and transition pieces

One of the simplest, but easiest ways to get a good idea of how to lay your Pergo laminate flooring is to read the instructions that come in the box. Many people never open the installation instructions that come with the product. Put yourself in an elite group and read the instructions! You will not regret it! You can also visit Pergo how-to pages for detailed installation instructions created for each Pergo laminate brand.

Can I tap laminate flooring during installation

Before Installation

Assuming you have chosen your floor already, open the boxes and allow them to come to room temperature by letting them adjust for at least 48 hours. The room temperature should be 60 degrees minimum. Cross stack the boxes in the room you will be installing them in. This will eliminate any potential warping or bending of the laminate planks.

While your floor is acclimating, you must remove all the moldings, baseboards, or heat registers on the floor that would interfere with the installation. If you decided to keep your wall base intact, you can cover the expansion gap with a quarter round molding, installed flush against the wall base.

Tip: When you purchase your laminate flooring, make sure you also purchase any thresholds, quarter round and base molding at the same time. This will save you time and money.

If the room is currently carpeted, the carpet, underlayment, tack strips, and tacks must be removed. Make sure the subfloor is clear, and if any floorboards are loose, nail them down to avoid squeaky floors.

Make sure the sub-floor is in good repair. If it is not intact, or smooth, make sure this is corrected before you lay the laminate foam underlayment.

When you are ready to lay your floor, determine which way you want your floor to go. Usually, the floor will look best when laid perpendicular from the windows. The light will shine on the length of the board and all the colors and patters will be noticeable.

Tip: When you remove the planks from the boxes, analyze each one. Some planks may work better as starter pieces, while others work better everywhere. Should you find several unacceptable planks, return them to your supplier and see what can be done to assist you with your situation.
Clean your subfloor before Standard Flooring Underlayment installation
Use your broom and clean your subfloor


Here you can find step-by-step instructions to have a successful installation!

Installing The Underlayment

It’s time to put down the underlayment. It must put down in stripes, butting but not overlapping. If it overlaps, your floor will end up uneven. The main reason for underlayment is to allow your floor to float; it will help with minor sub-floor imperfections and reduce noise. When the sub-floor is cement, vapor barrier is necessary- it prevents any potential humidity to come through the floor and ruin your Pergo.

Installing The First Row

Start with removing the tongue of the board facing the wall. Assemble the planks so they form a straight line. At a slight angle, insert the tongue of second laminate plank into the groove of first plank until the laminate edges meet, then press downward until the joint locks. Work from left to right. Any leftovers should not be thrown away. Save them, and reuse to start the next row. The distance between the wall and the first board should be at least ¼ inch. You can use spacers between the planks and the wall to allow for the required 1⁄4 inch expansion space (2 spacers placed together, thick side to thin side, equal 1⁄4 inch).

According to Pergo instruction you will need approximately one spacer per square foot of installation area. The bigger the room, the more expansion space should be left. That is necessary, because when the weather changes your floor expands and shrinks. When there is no or not enough space by the wall, your Pergo will get pressed against the wall and boards in the center of the room will buckle. That is the most common mistake during installation!

Installing The Second Row

If you are working alone, the easiest way to go is to use this method. You need to stager your first plank, to do it just cut the first plank of second row 2 feet in length and use it as your starter plank. Be sure that planks are locked properly and there is no gap between them! First click a long side of the starter plank into first row. Click next plank into the first row and lower this plank down until it is locked. Try to be as close as you can to the short side of the starter plank. Then, hit the short sides of the boards together using a tapping block. Continue to do that until you finish a row, and then start on the next one. If you are working with a group of people, it is much easier to assemble an entire row, and simply click it into the existing row all at once.

Continue to do that, all the way across the room. Measure and cut any openings in the floor, such as heat registers and doors. Also, undercut doors jambs, with a vibratory undercut saw. Remember! Never cut your laminate in the room in which you are working, because any saw dust or particles that get into the locking system of your floor could interfere with the proper functioning of the locks.

angle angle laminate installation

Finishing Touches

Install floor transitions; reinstall moldings, doors, heat registers, and you’re done!

Pergo Laminate Flooring

You have now completed your Pergo installation! If you have any tips, suggestions, or questions, please feel free to comment in the section below!

More Laminate Flooring Installation Tips:

About Bestlaminate

Bestlaminate’s blog is dedicated to you by making the home improvement process easier and more affordable. We hope to make your home remodeling and maintaining a more positive experience.

Check Also

Blog Header - Ask Bob & Betsy

What’s The Purpose Of The Wooden Wedge For Laminate Installation?

Hi May, We’re sorry to hear that you’re having troubles with an installation video! Sounds …

Installing Laminate Flooring on Stairs

For many homeowners, installing laminate flooring is one of the easiest and best ways to …

Your Guide to Installing Laminate Flooring On an Uneven Subfloor

Your guide to installing laminate flooring on an uneven subfloor requires you to pay attention …

Leave a Reply

Your email address will not be published. Required fields are marked *